GO-E HOMEfix 22kw Wallbox charger

GO-E HOMEfix 22kw Wallbox charger

The go-eCharger HomeFix 22 kW is a charging station with the highest performance at an unbeatable price-performance ratio. It is suitable for garages and outdoor parking areas, e.g. in front of residential buildings and companies (without selling charging current). The charging station has a 2 meters connection cable for a fixed connection to a power junction box. Thus, unlike the go-eCharger HOME+, the charger has no plug and is therefore not mobile. The clever solution for all who need a smart charging station for pure wall installation.

In addition to extensive safety functions such as DC fault protection (RCD protection module), phase detection and ground check, the box is equipped with RFID for access control (activation via app if required) and hotspot/WLAN. PV connection via the API interface, load balancing and electricity price exchange connection are also part of the functional scope. With the free go-eCharger app, comfort and basic settings can be changed, allowing you to adapt the device to your personal charging behavior.

Scope of delivery:

• Charging Station 22 kW* with 2 meters connection cable for stationary installation, without plug
• Wall bracket including screws and dowels
• Optionally mountable anti-theft device (U-piece)
• One reset card
• One RFID chip (already learned)
• Spare fine wire fuse
• Quick reference guide

Product specifications:

• Dimensions: approx. 15 x 25 x 9 cm
• Weight: approx. 2.47 kg
• Connection cable: 2 m, 5 x 6 mm² for permanent connection (Typ H07BQ-F)
• Rated voltage: 230 V (single-phase) / 400 V (three-phase)
• Mains frequency: 50 Hz
• Power grid types: TT/TN/IT
• Standby power: 1.9 W (LEDs switched off) to 4.2 W (LEDs bright)
• RFID: 13.56 MHz
• WiFi: 802.11b/g/n 2.4GHz / frequency band 2412-2472Mhz

Permissible ambient conditions:

• Installation site: indoors and outdoors, without direct sunlight
• Operating temperature: -25 °C to + 40 °C
• Storage temperature: -40 °C to + 85 °C
• Average temperature in 24 hours: below 35 °C
• Altitude: maximum 2,000 m above sea level
• Relative humidity: not more than 95 % (non-condensing)
• Impact resistance: IK10

Charging Capacity:

• Maximum charging power 22 kW (32 A 3-phase)
• Ampere and status Display: readable via LED ring and app
• Adjusting charging power: by button and app
• Charging power adjustable between 1.4 kW and 22 kW (via the charging current in 1 ampere steps between 6 A and 32 A) depending on the number of phases of the car‘s onboard charger:
  • Single-phase charging car: 1.4 kW to 7.4 kW (country-specific limitations need to be observed)
  • Two-phase charging car: 2.8 kW to 14.8 kW (two-phase connection of the charger is not possible)
  • Three-phase charging car: 4.2 kW to 22 kW (go-eCharger switches through the power that is available at the connection)

Connection to vehicle:

• Type 2 socket (IEC 62196-2) with mechanical locking device (own type 2 cable required, available as accessory)
• vehicles with type 1 can be charged with adapter cable type 2 to type 1 (available as accessories)

Safety functions:

• RCD protection module with DC current detection: 30 mA AC, 6 mA DC
• Protection class: I
• Pollution degree: II
• Anti-theft device: charging cable locking device
• RFID access control: one learned RFID chip included
• Input voltage: phase and voltage testing
• Switching functions: testing of the switching functions
• Ground check: for TT, TN grids (deactivatable ground check for IT grid – Norway mode)
• Current sensor: 3-phase
• Fine wire fuse: to protect the internal electronics (triggers if the supply line is connected incorrectly)
• IP54: protected against dirt and water, suitable for permanent outdoor operation (IP 44 when charging cable is plugged)
• go-e network operator API: for authorised access by the electricity grid operator to the go-eCharger for grid-serving power control
• Modbus TCP: e.g. for grid-serving power control by the electricity grid operator (from firmware version 0.40)

App and connectivity:

• Local (WiFi hotspot) or worlwide** (WiFi) controlling and monitoring
• Adjustment/check of the charge (voltage, current, power, energy)
• Adjusting the current level in 1 ampere steps
• Start/stop function
• Management of RFID chips/cards (up to 10 users per charger)
• Scheduler
• Electricity meter (total kWh and total amount per RFID chip)
• kWh limit mode
• Access control (RFID/App)
• Cable unlock functions
• Electricity price exchange connection (aWATTar mode) with intelligent charging management**/***
• static load balancing*
• Photovoltaic connection via open API interface (programming required)
• LED Adjustment
• Management of the charging levels via button on the charging Station
• Updateable for later functions (Smart home, etc.)
• Automatic unlocking of the charging cable in the event of a power failure
• 1-/3-phase switching via app – even during the charging process
• Synchronisation of charging processes with the cloud and display of the past charging processes
• Documented public API interfaces: HTTP, MQTT, Modbus TCP

Manufacturer GO-E, Austria.
Warranty 2 years.