Wall charging station GO-E Charger Gemini 11 kW

The price includes:

• 11 kW* charging station with 1.8 meter connecting cable for permanent installation
• Wall bracket including screws and dowels
• Optional mountable anti-theft device (U-shaped part)
• One reset card
• One RFID chip (already learned)
• Quick Reference Guide

Product Specifications:

• Dimensions: approx. 15.5 x 26 x 11 cm
• Weight: approx. 1.85 kg
• Connecting cable: 1.8 m, 5 x 2.5 mm² for permanent connection (Typ H07BQ-F)
• Nominal voltage: 230/240 V (single phase) / 400/415 V (three phase)
• Mains frequency: 50 Hz
• Types of electrical networks: TT/TN/IT
• Standby power: 3.1 W (LEDs off) to 5.2 W (LEDs bright)
• RFID: 13.56 MHz
• WiFi: 802.11b/g/n 2.4 GHz / Bandwidth 2412-2472 Mhz

Acceptable environmental conditions:

• Installation location: indoor and outdoor, without direct sunlight
• Operating temperature: -25 °C to + 40 °C
• Storage temperature: -40 °C to + 85 °C
• Average temperature for 24 hours: maximum 35 °C
• Altitude: maximum 2000 m above sea level
• Relative humidity: not more than 95% (non-condensing)
• Impact resistance: IK08

Charging capacity:

• Maximum charging power 11 kW (16 A 3-phase)
• Ampere and status display: readable via LED ring and app
• Charging power adjustment: by button and app
• Charging power adjustable between 1.4 kW and 11 kW (via charging current in steps of 1 amp between 6 A and 16 A) depending on the number of phases of the car’s on-board charger:
• Vehicle with single-phase charging: 1.4 kW to 3.7 kW (country-specific restrictions must be observed)
• Two-phase car charging: 2.8 kW to 7.4 kW (two-phase connection of the charger is not possible)
• Three-phase car charging: 4.2 kW to 11 kW (the go-e charger switches through the power that is available at the connection)

Vehicle connection:

• Socket type 2 (EN 62196-2) with mechanical locking device
• Type 1 vehicles can be charged with a Type 2 to Type 1 adapter cable

Safety features:

• RCD protection module with direct current detection: 20 mA AC, 6 mA DC
• Protection class: I
• Degree of pollution: II
• Anti-theft device: device to lock the charging cable
• RFID access control: one RFID chip included
• Input voltage: phase and voltage testing
• Switching functions: testing the switching functions
• Ground check: for TT, TN networks (disableable ground check for IT network – Norway mode)
• Current sensor: 3-phase
• Control serving the network: two data cables to connect to the ripple control receiver
• IP55 protected against dirt and water, suitable for permanent outdoor operation
• go-e network operator API: for authorized access by the electricity network operator to the go-e power management charger serving the network
• Modbus TCP: e.g. to manage the power serving the network by the electricity network operator

Application and Connectivity:

• Local (WiFi hotspot) or worldwide** (WiFi) management and monitoring
• Charge adjustment/check (voltage, current, power, energy)
• Current level adjustment in 1 amp increments
• Start/stop function
• Management of RFID chips/cards (up to 10 users per charger) / Access control (RFID/app)
• Planner
• Electricity meter (total kWh and total quantity per RFID chip)
• kWh limited mode / Eco mode** / Scheduled charging mode**
• Push Notifications**
• Cable unlock features
• Flexible energy tariffs with intelligent charge management**/***
• static load balancing**
• PV connection via open API (programming required)**
• OCPP 1.6**
• LED setup
• Control of charging levels via a button on the charging station
• Upgradable for later features (Smart Home etc.)**
• Automatic unlocking of the charging cable in the event of a power failure
• 1-/3-phase switching via app – even during the charging process
• Synchronize billing processes with the cloud and display past billing processes**
• Documented public APIs: HTTP, MQTT, Modbus TCP